« previous next »
Pages: 1 2 [3] 4

Author Topic: New Bolts  (Read 12754 times)

Offline Cutter

  • Hero Member
  • *****
  • Posts: 1174
New Bolts
« Reply #40 on: June 08, 2019, 10:51:44 AM »


I would like the info on the geared feed




 


I do not have a detailed drawing.

This .DXF is all I have

Good luck
Logged

Offline Cutter

  • Hero Member
  • *****
  • Posts: 1174
New Bolts
« Reply #41 on: June 12, 2019, 06:17:42 PM »
Cam is in and functioning.

I’ll try popping a blank tomorrow. 

 


Logged

Offline Cutter

  • Hero Member
  • *****
  • Posts: 1174
New Bolts
« Reply #42 on: June 13, 2019, 04:41:57 PM »
That’s about all I can do with one bolt

 


Logged

Offline gbull

  • Newbie
  • *
  • Posts: 52
New Bolts
« Reply #43 on: June 14, 2019, 09:59:49 AM »
Help is on the way. Package came from the lathe shop yesterday. Everything looks good. Hammer shafts out today for heat treat. Hopefully shipping out assemblies next week.
Logged

Offline maccrazy2

  • Full Member
  • ***
  • Posts: 229
New Bolts
« Reply #44 on: June 14, 2019, 11:34:22 AM »
Nice!
Logged

Offline Cutter

  • Hero Member
  • *****
  • Posts: 1174
New Bolts
« Reply #45 on: June 19, 2019, 03:40:48 PM »

Two hundred bolts might take longer to finish than the inspection model.


« Last Edit: June 19, 2019, 04:55:04 PM by Cutter »
Logged

Offline 4171

  • Newbie
  • *
  • Posts: 124
New Bolts
« Reply #46 on: June 19, 2019, 06:10:33 PM »
Very nice Jerry. I see you made it direct drive. Do you have a way to set headspace or does it matter?

Mike
Logged

Offline Cutter

  • Hero Member
  • *****
  • Posts: 1174
New Bolts
« Reply #47 on: June 19, 2019, 07:17:14 PM »


Very nice Jerry. I see you made it direct drive. Do you have a way to set headspace or does it matter?

Mike




 


Yes Mike,

Front and rear nuts with set screws and a wad of nylon. 
Logged

Offline Cutter

  • Hero Member
  • *****
  • Posts: 1174
New Bolts
« Reply #48 on: June 21, 2019, 01:15:51 PM »
My wife decided she wants the 12 lb model

when I’m finished with the bolts, also wanted

her name on it, in Kanji ( She’s Japanese )

« Last Edit: June 21, 2019, 01:19:08 PM by Cutter »
Logged

Offline drhardin

  • Global Moderator
  • Full Member
  • *****
  • Posts: 136
New Bolts
« Reply #49 on: June 21, 2019, 01:21:06 PM »

You are tooooooo much....Love it

Logged

Offline Sparky_NY

  • Sr. Member
  • ****
  • Posts: 481
New Bolts
« Reply #50 on: June 21, 2019, 02:46:38 PM »


 


My wife decided she wants the 12 lb model

when I’m finished with the bolts, also wanted

her name on it, in Kanji ( She’s Japanese )

 




How do you get those surfaces with no hint of tooling marks?

Logged

Offline Cutter

  • Hero Member
  • *****
  • Posts: 1174
New Bolts
« Reply #51 on: June 21, 2019, 03:55:27 PM »


How do you get those surfaces with no hint of tooling marks?




 


The kanji was roughed with a .010 step over, and

finished with .002 step over and .002 in Z with

a .0625 ball mill

Scotch-Brite pad cleans it up good.

Still some tool marks, but close enough for my little Nip.

« Last Edit: June 21, 2019, 05:54:52 PM by Cutter »
Logged

Offline Cutter

  • Hero Member
  • *****
  • Posts: 1174
New Bolts
« Reply #52 on: June 22, 2019, 07:46:20 PM »


With the stick do you have the stick down close enough to the carrier only one shell can come out and as it rotates to the next barrel the next shell loads?




 


gbull, this is the action I get with a .160 gap between magazine and flat

 


« Last Edit: June 22, 2019, 07:49:12 PM by Cutter »
Logged

Offline Cutter

  • Hero Member
  • *****
  • Posts: 1174
New Bolts
« Reply #53 on: June 30, 2019, 10:55:03 AM »
I received the 200 bolts Saturday morning.

After spending 3 to 4 hours unwrapping, counting, an inspecting,

I realized how much more time it took to get them to this point.

Thank You gbull , for your many hours.  

Logged

Offline gbull

  • Newbie
  • *
  • Posts: 52
New Bolts
« Reply #54 on: June 30, 2019, 02:21:12 PM »

I received the 200 bolts Saturday morning.

After spending 3 to 4 hours unwrapping, counting, an inspecting,

I realized how much more time it took to get them to this point.

Thank You gbull , for your many hours.


Thank you and the others for motivating me to act and quit being a lurker on this forum.

Logged

Offline Cutter

  • Hero Member
  • *****
  • Posts: 1174
New Bolts
« Reply #55 on: July 06, 2019, 08:11:34 PM »
Getting started on the first operation.

Cutting the follower, radius and flats.

 


Logged

Offline Cutter

  • Hero Member
  • *****
  • Posts: 1174
New Bolts
« Reply #56 on: July 10, 2019, 06:57:51 PM »
received 30 end mills today, We’ll see how long they last

Probably about two months before I ship.

I have some pre-planned trips for the Summer

Logged

Offline maccrazy2

  • Full Member
  • ***
  • Posts: 229
New Bolts
« Reply #57 on: July 11, 2019, 10:31:56 AM »
Just got back from Florida myself for some much needed R&R
Logged

Offline gbull

  • Newbie
  • *
  • Posts: 52
New Bolts
« Reply #58 on: July 16, 2019, 09:31:01 PM »
Back to the public topic. The price for wire edm cut extractors comes to $4.10 each. That does not include the spring and plunger. We can get a bulk rate price on the springs and I think we can all make our own plungers, unless someone wants to handle them. I am hoping to have a price on machining the rest of the bodies complete. Without a complete gun it is hard to sell a complete assembly since I am not that far along to have a shooting platform to be able to verify functionality. Any thoughts?
Logged

Offline maccrazy2

  • Full Member
  • ***
  • Posts: 229
New Bolts
« Reply #59 on: July 16, 2019, 10:08:14 PM »
I’m in for some extractors. I’ll know how many shortly.

Awaiting the quote for machining to complete the bolts.
Logged
Pages: 1 2 [3] 4
« previous next »