Author Topic: Rat Gat (Read 61413 times)

Cutter · « **Reply #260 on:** February 26, 2016, 10:36:14 AM »

I changed the leg position on the bull barrel and shortened
the crank lever to clear the magazine adapter when it\'s open.

Cutter · « **Reply #261 on:** March 06, 2016, 07:08:47 PM »

Cutting the new rotors for the 75 round magazines, this is for
the group build. One of the guys supplied some high density polyethylene,
which should work very well , it\'s slipperier then snot.
The first one was black delrin.

Cutter · « **Reply #262 on:** March 09, 2016, 07:11:25 PM »

Going to the ranch for testing tomorrow.

Tools, note book, and 500 rounds.

Whatever happens , I\'ll post it Friday

4171 · « **Reply #263 on:** March 10, 2016, 12:28:09 PM »

Hope nobody pulls you over. Lol I might mess my pants if I saw that.

Mike

Cutter · « **Reply #264 on:** March 11, 2016, 11:51:35 AM »

I had a little trouble with the bull barrel.

Spent casings like the X marks the spot, and jams.

I have another new cartridge carrier like the one in Shorty

going in soon. Good news no misfires .

I could only hand feed Shorty, no misfires, but I need

to adjust the preload on the firing pin.

It\'s a little heavy.

Never give up

joboxxer · « **Reply #265 on:** March 16, 2016, 03:27:24 PM »

What is the size and location of your ejection port?

Cutter · « **Reply #266 on:** March 16, 2016, 09:17:25 PM »

The cam in the six barrel has been modified for a rapid return.

It\'s nothing like the RG-G cam

joboxxer · « **Reply #267 on:** March 17, 2016, 01:08:52 PM »

I didn\'t realize you had done that. So I guess on mine it will eject closer to 45 degrees before TDC?

joboxxer · « **Reply #268 on:** March 17, 2016, 02:55:05 PM »

Scratch that. After closer study, it\'s more like around 120 degrees b4 TDC.

Cutter · « **Reply #269 on:** March 30, 2016, 11:04:07 AM »

joboxxer,
I set the ejection angle at 90Â° BTDC

Cutter · « **Reply #270 on:** April 03, 2016, 08:59:36 PM »

A 6\" Riser pipe 2\' long, foam rubber, and duct tape from Home Depot.

Testing with low power blanks in the garage.

Cutter · « **Reply #271 on:** April 08, 2016, 12:44:06 PM »

I\'ve decided to put a stick magazine on Shorty, cut the adapter

yesterday. This works much faster than the rotary feed with the

configuration of the other parts, bolts, carrier, and so on.

lockguy2 · « **Reply #272 on:** April 08, 2016, 08:37:24 PM »

Thanks! I really enjoy looking at your stuff.

Dan

Cutter · « **Reply #273 on:** April 09, 2016, 12:08:18 PM »

I made a short temporary stick to test Shorty.
Smells good.

Cutter · « **Reply #274 on:** April 16, 2016, 11:48:45 AM »

A little slow, even for an old-timer

Cutter · « **Reply #275 on:** April 22, 2016, 07:04:29 PM »

Went through 450 rounds today

More videos comming

Sparky_NY · « **Reply #276 on:** April 23, 2016, 07:24:10 AM »

Runs like a fine watch, no surprise with the class of work you always produce.

Be putting the machines into place in my shop within the next week. Following your work keeps me motivated !

Cutter · « **Reply #277 on:** April 23, 2016, 10:19:36 AM »

Thanks Sparky !
I cant wait to see the video from the drone.
Probably next week.

Dennis · « **Reply #278 on:** April 24, 2016, 10:08:45 AM »

Drone?? I can\'t wait either!

Sparky_NY · « **Reply #279 on:** April 24, 2016, 10:33:50 PM »

Was the drone the target? LOL

News:

Author Topic: Rat Gat (Read 61413 times)