Author Topic: Rat Gat (Read 61416 times)

Cutter · « **Reply #240 on:** November 25, 2015, 10:29:07 AM »

You answered your questions Sparky

Cutter · « **Reply #241 on:** November 25, 2015, 10:30:05 AM »

Received the hammers for the joint build. Great job Mike!

Hammers made from O1 ,

Cutter · « **Reply #242 on:** November 28, 2015, 08:54:16 PM »

Upper mount finished.

9\" spread at the bottom. 10\' height to C/L

Angled to get 3\" forward

Cutter · « **Reply #243 on:** November 30, 2015, 03:48:46 PM »

Legs to cheeks, cheeks to body

Cutter · « **Reply #244 on:** December 15, 2015, 02:25:52 PM »

Setting on all three now.

The rear leg has a left hand thread on top and

right hand on bottom, gives about 10Â° adjustment each way.

Next year for the magazine.

Take care , have a good one

joboxxer · « **Reply #245 on:** January 07, 2016, 03:49:13 PM »

Are you going to heat treat the hammers? O1

Cutter · « **Reply #246 on:** January 08, 2016, 11:28:12 AM »

Yes on heat treat.

O1 can easily be hardened at home.

joboxxer · « **Reply #247 on:** January 27, 2016, 12:06:45 PM »

Looking at your breech backplate on page 8, I don\'t see a bolt extractor port. Not really needed?

Cutter · « **Reply #248 on:** January 27, 2016, 05:17:38 PM »

joboxxer

I use no bolt extractor.

I unscrew the cascabel & cocking switch knobs,

and remove the breech plate. Access through

the recoil plate, finger push. The aluminum plug

you see just keeps the bolt on track.

Cutter · « **Reply #249 on:** January 27, 2016, 09:32:44 PM »

My wife uses my rejects/scrap
barrel shroud

4171 · « **Reply #250 on:** January 28, 2016, 02:39:28 PM »

Great job of recycling! :cool:

Mike

Dave · « **Reply #251 on:** January 29, 2016, 07:32:57 PM »

My wife uses my rejects/scrap

barrel shroud

Now thats funny!

4171 · « **Reply #252 on:** February 06, 2016, 12:07:50 PM »

Any one of the coop builders have the diagram for the casing. Mine shows the opening for the magazine as .3200 x 1.25 I do not believe that is correct and Cutter is on vacation :mrgreen:

Mike

Cutter · « **Reply #253 on:** February 10, 2016, 06:41:54 PM »

Problem solved, that dam little decimal point again.

.3200 --------3.200

joboxxer · « **Reply #254 on:** February 11, 2016, 12:41:41 PM »

Do you cut the half inch slot in the box cam?

Cutter · « **Reply #255 on:** February 11, 2016, 06:15:31 PM »

Nope,
I left about .060 clearance for the follower.

joboxxer · « **Reply #256 on:** February 25, 2016, 02:30:31 PM »

Can you throw any details about the cocking ring and switch? I\'m staring at this offset cut on the segments trying to decide how I want to do it.

Cutter · « **Reply #257 on:** February 25, 2016, 03:36:30 PM »

[attachment=10306:Switch 3.JPG]joboxxer,

I make a one piece cocking ring, use a woodruff cutter

.094 X .312

joboxxer · « **Reply #258 on:** February 25, 2016, 03:49:18 PM »

Great minds think alike. I just did exactly that. What is the tall part at the sear release hole for? Do the bolts have to go between that or are the short of it? I like how you made the cocking switch work.

Cutter · « **Reply #259 on:** February 25, 2016, 04:36:27 PM »

The head of the shear screw drops through, then recoil between the high point and bolt cap

News:

Author Topic: Rat Gat (Read 61416 times)