Author Topic: Rat Gat (Read 61419 times)

Cutter · « **Reply #160 on:** May 08, 2015, 04:19:42 PM »

Here\'s the information to contact the seller.
Keep in mind, my price was for a quantity of 18

Chris Teeter
ctetter@centurylink.net

Cutter · « **Reply #161 on:** May 13, 2015, 08:20:14 PM »

A little more progress on this co-op build.
One of the guys bored the bolt carriers and
put in the slot for the drive pin, and I finished the
cartridge carriers and alignment holes.
Cartridge carriers are 303 stainless.

Cutter · « **Reply #162 on:** May 15, 2015, 06:14:27 PM »

We are still looking for partners in this build.
I would like someone to do the lathe work on the bolts.
Here\'s what I\'m thinking,
Someone to supply material (303 stainless) and 58 bolts to this sketch.
In return you get both carriers, barrel plate, and 7 of the
bolts after they are finished on the CNC mill.
Open to questions & suggestions.

Cutter · « **Reply #163 on:** May 28, 2015, 11:29:53 AM »

I cut 6 \" off stock 10/22 barrels.

I\'m planning on exposed rotating barrels. ( no frame to the front )

Bolts are in process, still one slot open

Cutter · « **Reply #164 on:** May 30, 2015, 12:02:02 PM »

I made a fixture with a taper for holding the stock barrels.
( .4Â° taper per side )

Cutter · « **Reply #165 on:** July 09, 2015, 05:09:53 PM »

Had a little get together with some other builders.

And there\'s two more out there.

Cutter · « **Reply #166 on:** July 15, 2015, 09:55:52 PM »

After tweaking the geometry & spring tension a little more, It seems
to flip out the casing consistently, 75 times anyway.
I\'m also changing the drum drive gear, mounting gear segments on the bolt carrier
instead of the gear on the cartridge carrier.

gbull · « **Reply #167 on:** July 18, 2015, 01:11:46 AM »

Any hints on how you get the round to eject and jump off the bolt so neatly? I watched the video a bunch and I\'m stumped. Nice job!

DonLans · « **Reply #168 on:** July 18, 2015, 09:01:14 AM »

I\'m constantly amazed at everything Cutter does. Any chance of putting the Mars Rover pictures back up?

Cutter · « **Reply #169 on:** July 18, 2015, 02:09:01 PM »

Hi gbull,
I have the extractor rotated as far to the right as possible applying
uneven spring pressure on the casing causing it to flip out as soon
as it clears the chamber. My first attempt about three years ago
was with the extractor on top, but the even pressure would hold it in place,
sometimes release it, never knew where it would go.

Notice the slot in the original pan for a kicker, pan
is in 4 parts now. Works good, I\'m not changing that.

Trial & Error

Dave · « **Reply #170 on:** July 18, 2015, 04:15:33 PM »

Very amazing work!!!!

Cutter · « **Reply #171 on:** July 19, 2015, 03:58:57 PM »

Gear segments are ready for other builders.

Ship this week, assembly required

Cutter · « **Reply #172 on:** July 21, 2015, 10:47:05 AM »

After cutting off the stock barrels I now
have some short barrels for , you guest it

6-1/4 \"

Cutter · « **Reply #173 on:** July 24, 2015, 08:24:57 PM »

Some new pictures of Shorty

Sparky_NY · « **Reply #174 on:** July 25, 2015, 09:10:21 PM »

Will the short barrel version be known as a Mouse Gat?

Cutter · « **Reply #175 on:** July 26, 2015, 12:23:25 PM »

That\'s what we need a Spark to ignite this fading forum.

Have your retrofit ready to go yet ?

Cutter · « **Reply #176 on:** July 26, 2015, 12:24:48 PM »

I\'ll use the small bolt for the 6\" barrels

Sparky_NY · « **Reply #177 on:** July 26, 2015, 10:11:33 PM »

That\'s what we need a Spark to ignite this fading forum.

Have your retrofit ready to go yet ?

I have not worked on the mill in quite a while, I got the electronics done and the Z under motion, the X and Y remain. I got sidetracked ! I built a 32x50 pole barn for a workshop, 10ft ceiling. It was a lot of work and the end is in sight now, pretty much down to some wiring and pouring the floor. Gonna be a hell of a shop, something I have always wanted but never had the room. Meanwile, I picked up a jet 14x40 lathe a few months back, a big improvement from the 9x20 I had.

Cutter · « **Reply #178 on:** July 31, 2015, 11:08:47 AM »

I received the cam and cocking ring blanks from one of our builders.
This co-op build is progressing

Cutter · « **Reply #179 on:** August 03, 2015, 11:22:59 AM »

I mounted the front bearing on the bearing plate.

This is the short barrel version.

News:

Author Topic: Rat Gat (Read 61419 times)